Hi

Contact us for more discounted prices!

Get a Quote

Consult Our Engineers & Get Fast Official Quotation

Security verification
SUBMIT

How is the torsional strength of drill pipe joints calculated? API RP 7G: Guidelines for Make-up Torque and Safety Margin

Author:

WHH

Source:

LONGWAY

Published:

2026-11-20


In directional and extended-reach wells, torque often represents the bottleneck limiting drilling operations. If the torque exceeds the load‑carrying capacity of the drill pipe joints, the joints may bulge and deform in mild cases, or shear off or fracture downhole in severe cases.

Many purchasers, when buying drill pipes, focus solely on whether the steel grade is S135, overlooking the connection’s torsional strength. In fact, in most deep and horizontal wells, the weak link in the drill string’s torsional resistance is often the tool joint ( Tool Joint ), rather than the pipe body.

Today, in conjunction with API RP 7G, we’ll discuss how to properly determine the torsional strength of connections and the make-up torque used on-site.

1. Why is the torsional strength of a joint weaker than that of the pipe body?

Drill pipe joints are connected via threads; to machine these threads, the interior of the joint must be bored and the exterior turned. This results in a thread root cross-sectional area that is typically smaller than that of the pipe body.

In API standards, “joint efficiency” is often used as a measure. Typically, the torsional strength of a standard API joint is about 80% to 95% of the yield strength of a pipe of the same size. This means that under extreme torque, failure usually occurs at the joint first.

II. How is torsional strength calculated? Refer to the API formula.

API RP 7G provides relatively complex formulas for calculating torsional strength. For field engineers, the most practical approach is to use a tabular method (Table 10 of API RP 7G and the associated parameter tables).

But you need to understand several core variables:

1. Material yield strength: The yield strength of S135 is significantly higher than that of G105; therefore, for couplings of the same size, S135 exhibits greater torsional resistance.

2. Joint outer diameter (OD) and inner diameter (ID): The larger the outer diameter and the smaller the inner diameter (i.e., the thicker the wall), the greater the joint’s torsional resistance.

3. Thread Type: NC‑type connections exhibit superior stress distribution compared to older IF or REG connections. Double Shoulder (DSTJ) connections, by incorporating an additional secondary shoulder, can improve torsional resistance by 20%–50% relative to standard connections.

III. The most common pitfall on site: How do you determine the make-up torque?

Once the ultimate torque that the joint can withstand has been calculated, what tightening torque should be applied on site?

Key point: Tightening torque is neither “the higher the better” nor something to be determined “by feel.”

1. According to the recommended values in API RP 7G: API provides recommended make-up torque ranges based on connection size and steel grade.

2. Be mindful of the effect of thread sealant: API’s recommended torque values are typically based on a friction coefficient of 0.08. If you use a high-friction thread sealant (such as some copper- or zinc-based compounds), the actual joint preload will be higher. Failure to adjust accordingly can lead to over-tightening and galling. When switching to a different thread sealant, always recalculate the required torque!

3. Don’t forget to record the torque curve: Nowadays, even relatively good drilling rigs are equipped with torque meters. If, during make-up, the torque curve doesn’t rise smoothly but instead shows sudden fluctuations, it indicates that the threads may be damaged or misaligned. Stop immediately, disassemble for inspection, and avoid forcing the connection.

IV. How to prevent torque failure on site?

Inspect threads regularly: Many thread‑seizing incidents occur because excessive wear reduces the actual contact area. Even when you’re exhausted after pulling out of hole, take a moment to check the threads.

Controlling dogleg severity: In areas with high dogleg severity, the drill pipe is subjected not only to torsion but also to bending. Bending reduces a portion of the joint strength.

Use Double Shoulder Tool Joint (DSTJ): For extended-reach wells or wells with very long horizontal sections, it is recommended to use double shoulder tool joints directly. Although they are more expensive, they provide a significantly larger safety margin.

Need to calculate drillstring torque or purchase high-torque-resistant drill pipe?

Our company manufactures drill pipes and double-tapered (double‑taper) connections that comply with API 5DP and API 7‑1 standards. All our connections are forged from high‑quality AISI 4145H alloy steel and undergo rigorous heat treatment to ensure they meet the required torsional and fatigue performance specifications.

If you are uncertain about torque margin when designing your drill string, or if you need to procure API drill pipe with high torsional resistance, please contact our technical team. Send us your well depth, dogleg severity, and estimated weight on bit, and we can help calculate the required joint specifications and provide a complete MTC report.


Leave Message

Consult Our Engineers & Get Fast Official Quotation

Security verification
SUBMIT

Give you the best solution

  1. Inquiries get a response within 12 hours.
  2. We are a professional manufacturer with competitive pricing, and we accept all DEM/ODM orders.
  3. Our after-sales team provides 24/7 technical support; issues are addressed within 24 hours.
  4. Precision quality, on-time delivery, tailored service.

Recent Blogs